Lithofin MN Stain Stop - 1LTR- Natural Stone Impregnator & Sealer

Your Price: €102.25 (€83.13 exc VAT)
Part Number:11610/20559

Optimal protection for absorbent, stain sensitive natural stone surfaces. Lithofin Stain Stop largely prevents penetration of oil, grease, and water. Highly recommended in kitchens and bathrooms. Ideal for indoor, outdoor use on all stones, effective for many years. No gloss. 


A spirit-based, silicone impregnator that penetrates the surface of stone and forms an invisible film within the pores and capillaries. Prevents staining from water, dirt, and oil, allowing the stone to breathe, and aids maintenance. For use on all polished and unpolished natural and artificial stone.

A special, ready-to-use product from the Lithofin range for marble, natural and artificial stone. Lithofin MN Stain-Stop contains silicones and hardeners that repel water and oil effectively. Lithofin MN Stain-Stop penetrates the surface and forms a thin, invisible film in the capillaries. This stops oils from penetrating the surface for about 6-24 hours for marble and granite and up to 8 days for limestone. Within this time, it is possible to wipe away oils without leaving stains. The effect depends on the absorbed quantity of the product. Using Lithofin MN Stain-Stop does not usually affect the appearance of the stone; however, some intensification of colour may occur in darker stone types. It is UV resistant (yellowing of stone will not occur) and dries without leaving a sticky residue. The active ingredients pose no health hazard after drying

Field of application and suitable surfaces:
Lithofin MN Stain-Stop is used as a stain repellent for all marble, natural and artificial stone surfaces. Particularly suitable for walls and floors of kitchens, bathrooms, and other areas at risk from staining, as well as for tabletops, windowsills, and domestic surfaces. Polished and ground marble, polished and natural cleft limestone, slate, varying finishes of granite, reconstituted stone, artificial stone, terrazzo, and resin bonded stone.

Please note:
With polished marble, red wine, ketchup, or cola can cause etching. Never allow Lithofin MN Stain-Stop to dry on the surface, as it is not easily removed. Only to be used on absorbent and dry surfaces. Glass, ceramics and surfaces sensitive to solvents must be protected. A test area is advised before full treatment.

Directions for use:
The stone surfaces to be treated must be clean and dry. On an absorbent surface, apply generously and evenly with a brush or lamb’s wool roller. On less absorbent surfaces apply with a brush or cloth. Within 30-40 minutes, treat the surface again to permit the impregnator to be absorbed. Then after 30 minutes remove any residue completely using a cloth. Over large surfaces draw off excess material using a window rubber and polish using a using a pneumatic scrubbing machine with a 3m polishing pad.

dependent on absorbent properties of stone: about. 15m2/L for polished stone surfaces. About 6-8m2/L, for natural and sawn stone. About 3-6m2/L, for porous sandstone and highly porous limestone.

Drying time:
preliminary drying: 2 hours (safe to walk on with smooth sole shoes). Complete drying: 24-48 hours (full effectiveness of impregnator).

After Treatment:
for regular washing of floors we recommend Lithofin Easy-Care Cleaner, which supports the effect of Lithofin MN Stain-Stop.

Used outdoors, Lithofin MN Stain-Stop is effective for about 5-10 years. Used indoors, durability depends on aftercare products but expect Lithofin MN Stain-Stop to remain effective for up to 10 years with the correct ongoing maintenance.

Keep out of reach of children. Ensure good ventilation during and after application. Do not use large quantities in rooms in which open, or lightly wrapped foodstuffs are stored. Avoid naked flames. Labelling requirements in accordance with Dangerous Material Regulations or EC Guideline 88/379: Inflammable. RID/ADR: Class 3, No. 31c (does not apply to cartons with 0,5 L, 1 L or 5 L).

According to EC recommendation: siloxane, isoparaffins, white spirit.

In a dry, cool place. Closed containers have a shelf life of at least 12 months.

Technical data:
Density: 0,78g/cm3
Flashpoint: 22°C
Appearance: colourless
Odour: white spirit, ethylacetate
Reduction of water absorption: 90-95%
Water vapour permeability: 80-90%

1 litre bottle with childproof cap 

Environmental protection:
Contains organic solvents, free of chlorinated hydrocarbons.

Hand over to special waste collectors. Empty containers, which are clean or have dried out may be recycled.

This information is provided without guarantee. The product should be used considering the local conditions and the surface to be treated. In all cases of doubt, test the product first in an inconspicuous area.

Related Items